Mitsubishi Colt (with 1983 for 1993 of release)
1. The maintenance instruction of cars Mitsubishi Colt / Lancer / Mirage / Galant / Eterna / Saporro / Sigma / Magna / Cordia / Tredia / Precis with 1983 for 1993 of release
2. Adjustment and current maintenance service
3. The engine
4. An engine partition
4.1. Technical characteristics
4.2. The general description
4.3. Engine major repairs - the general remarks
4.4. Diagnostics of the engine by means of the vacuum gauge, check of a compression and dismantle of the power unit (security measure)
4.5. Installation of the piston of cylinder N 1
4.6. Engine removal - the general description
4.7. The engine - removal and installation
4.8. Engine major repairs - alternative methods
4.9. An engine partition - a dismantling order
4.10. A head of the block of cylinders - dismantling
4.11. A head of the block of cylinders - clearing and survey
4.12. Valves - repair and installation
4.13. A head of the block of cylinders - assemblage
4.14. Pistons and rods - removal
4.15. A cranked shaft - removal
4.16. The block of cylinders - clearing
4.17. The block of cylinders - survey
4.18. Хонингование cylinders
4.19. Pistons and rods - survey
4.20. A cranked shaft - survey
4.21. Loose leaves radical and шатунных bearings - survey
4.22. An engine partition - an assembly order
4.23. Piston rings - installation
4.24. A cranked shaft - installation and check of a lubricant backlash of radical bearings
4.25. Installation of a back epiploon of a cranked shaft
4.26. Pistons and rods - installation and check of a lubricant backlash of the bearing
4.27. The first start of the engine after a partition
5. Systems of cooling, heating and an air conditioning
6. The power supply system and release of the fulfilled gases
7. An engine electric equipment
8. Systems of decrease in toxicity of exhausts
9. A mechanical transmission
10. An automatic transmission
11. Coupling and semiaxes
12. Brake system
13. A suspension bracket and a steering
14. A body
15. A body electric equipment
 











4a8e3442

4-13-golovka-bloka-cilindrov-sborka.html

4.13. A head of the block of cylinders - assemblage

1. Carefully clear a head before the assemblage beginning.

12.2 the deep plug or the special tool is necessary For installation of consolidation of the valve

1. The special tool
2. Consolidation
3. A spring saddle


2. Establish new consolidations on directing plugs of inlet valves (12.2).

12.3 If in a head the enameled springs of valves have been established, establish their enameled ends from a head, as is shown in drawing
1. The enameled end of a spring
2. A plate
3. Consolidation
4. A spring saddle


3. Grease and establish the first valve. Establish a spring saddle on directing plug and establish a spring and a plate (12.3).

12.4 Grease сухарики with greasing before installation


4. Compress a spring and establish сухарики, preliminary having greased them (12.4).
5.  Similarly  establish other valves.

12.6 Check up height of installation of a spring of the valve


6. Check up height of installation of valves. It is measured from the top surface of a saddle of a spring of the valve to the bottom surface of a plate (12.6). If height too big, establish washers under a spring.

12.7 For replacement of consolidation of the valve of an admission of the rarefied mix the special tool is used
1.MD998308
2. Consolidation
3. The valve case
4.MD998308


7. By means of tool N MD998308 establish consolidation on a rod of the valve of an admission of the rarefied mix (12.7).
8. Grease a rod of the valve and establish it into place.
9. Compress a spring by means of tool N MD998309 and establish it together with a plate. Establish сухарики.

12.10 At installation of valves of an admission of the rarefied mix use new sealing rings. Grease rings, a carving and a saddle with engine oil (are specified by arrows)


10. Establish a new sealing ring on the valve and grease with its engine oil (12.10). Also grease a carving and a saddle.
11. Establish valves of an admission of the rarefied mix and tighten them till the demanded moment of an inhaling.
12. Grease молибденовой with greasing коромысла, a camshaft and axes коромысел, then establish a camshaft, коромысла and axes коромысел into place.


4.12. Valves - repair and installation

4.14. Pistons and rods - removal