Mitsubishi Colt (with 1983 for 1993 of release)
1. The maintenance instruction of cars Mitsubishi Colt / Lancer / Mirage / Galant / Eterna / Saporro / Sigma / Magna / Cordia / Tredia / Precis with 1983 for 1993 of release
2. Adjustment and current maintenance service
3. The engine
4. An engine partition
4.1. Technical characteristics
4.2. The general description
4.3. Engine major repairs - the general remarks
4.4. Diagnostics of the engine by means of the vacuum gauge, check of a compression and dismantle of the power unit (security measure)
4.5. Installation of the piston of cylinder N 1
4.6. Engine removal - the general description
4.7. The engine - removal and installation
4.8. Engine major repairs - alternative methods
4.9. An engine partition - a dismantling order
4.10. A head of the block of cylinders - dismantling
4.11. A head of the block of cylinders - clearing and survey
4.12. Valves - repair and installation
4.13. A head of the block of cylinders - assemblage
4.14. Pistons and rods - removal
4.15. A cranked shaft - removal
4.16. The block of cylinders - clearing
4.17. The block of cylinders - survey
4.18. Хонингование cylinders
4.19. Pistons and rods - survey
4.20. A cranked shaft - survey
4.21. Loose leaves radical and шатунных bearings - survey
4.22. An engine partition - an assembly order
4.23. Piston rings - installation
4.24. A cranked shaft - installation and check of a lubricant backlash of radical bearings
4.25. Installation of a back epiploon of a cranked shaft
4.26. Pistons and rods - installation and check of a lubricant backlash of the bearing
4.27. The first start of the engine after a partition
5. Systems of cooling, heating and an air conditioning
6. The power supply system and release of the fulfilled gases
7. An engine electric equipment
8. Systems of decrease in toxicity of exhausts
9. A mechanical transmission
10. An automatic transmission
11. Coupling and semiaxes
12. Brake system
13. A suspension bracket and a steering
14. A body
15. A body electric equipment
 





4a8e3442






4-7-dvigatel-snyatie-i-ustanovka.html

4.7. The engine - removal and installation

Removal
1. If on the car air central air is established, discharge it, having addressed to experts.
2. Close old blankets forward wings.
3. Remove a cowl.
4. Disconnect and remove the accumulator.
5. Remove the air filter. Remove an inlet branch pipe турбокомпрессора if it is necessary.
6. Merge cooling liquid and remove a radiator.

6.7 Mark all wires before a detachment of a socket of connection


7: Mark and disconnect all hoses, tubes, wires and ropes (6.7).
8. Lift the engine and establish it on support.
9. Remove the conditioner compressor, the pump and a tank of system of hydrostrengthening of a steering.
10. Merge oil and a liquid of a transmission and remove the oil filter.
11. Disconnect a reception pipe from a final collector.
12. Disconnect semiaxes from a transmission and close apertures in a transmission rags.

6.13 Connect a lift chain to arms on the engine by means of the big bolts and washers


13. Connect the lift to arms of the engine (6.13).
14. Establish a jack under a transmission.

6.15 On some models it is necessary to remove the main brake cylinder and a fixing arm of a transmission (are specified by arrows) (the model with volume of the engine 1,5 is shown)


15. Remove the main brake cylinder and an arm of a transmission (6.15) if it is necessary.

6.16 Remove a long through bolt from transmission fastening


16. Remove a through bolt of fastening (6.16).
17. Check up, that all ropes, hoses, wires and other elements have been disconnected from the engine.

6.18 Slowly lift the engine, lowering a transmission


18. Accurately raise the engine and lower a transmission (6.18).
19. Accurately lift the engine and a transmission and remove them from the car.
2О. Remove a transmission from the engine and remove elements of coupling and a flywheel (or a conducted disk).
Installation
20. Check up engine and transmission fastenings. Replace them if they are damaged.
21.  Check up elements of coupling and grease шлицы an entrance shaft with high-temperature greasing.
22. Establish a transmission on the engine, and reliably tighten fixing bolts.
23. Connect the lift to the engine and establish it on the car.
24. Establish fixing bolts, and reliably tighten them.
25. Establish all other elements and fastenings upside-down removals.
26. Fill in cooling liquid, oil, a liquid of system of hydrostrengthening of a steering and трансмиссионное oil.


4.6. Engine removal - the general description

4.8. Engine major repairs - alternative methods