Mitsubishi Colt (with 1983 for 1993 of release)
1. The maintenance instruction of cars Mitsubishi Colt / Lancer / Mirage / Galant / Eterna / Saporro / Sigma / Magna / Cordia / Tredia / Precis with 1983 for 1993 of release
2. Adjustment and current maintenance service
3. The engine
4. An engine partition
4.1. Technical characteristics
4.2. The general description
4.3. Engine major repairs - the general remarks
4.4. Diagnostics of the engine by means of the vacuum gauge, check of a compression and dismantle of the power unit (security measure)
4.5. Installation of the piston of cylinder N 1
4.6. Engine removal - the general description
4.7. The engine - removal and installation
4.8. Engine major repairs - alternative methods
4.9. An engine partition - a dismantling order
4.10. A head of the block of cylinders - dismantling
4.11. A head of the block of cylinders - clearing and survey
4.12. Valves - repair and installation
4.13. A head of the block of cylinders - assemblage
4.14. Pistons and rods - removal
4.15. A cranked shaft - removal
4.16. The block of cylinders - clearing
4.17. The block of cylinders - survey
4.18. Хонингование cylinders
4.19. Pistons and rods - survey
4.20. A cranked shaft - survey
4.21. Loose leaves radical and шатунных bearings - survey
4.22. An engine partition - an assembly order
4.23. Piston rings - installation
4.24. A cranked shaft - installation and check of a lubricant backlash of radical bearings
4.25. Installation of a back epiploon of a cranked shaft
4.26. Pistons and rods - installation and check of a lubricant backlash of the bearing
4.27. The first start of the engine after a partition
5. Systems of cooling, heating and an air conditioning
6. The power supply system and release of the fulfilled gases
7. An engine electric equipment
8. Systems of decrease in toxicity of exhausts
9. A mechanical transmission
10. An automatic transmission
11. Coupling and semiaxes
12. Brake system
13. A suspension bracket and a steering
14. A body
15. A body electric equipment
 











4a8e3442

4-10-golovka-bloka-cilindrov-razborka.html

4.10. A head of the block of cylinders - dismantling

1. Remove axes коромысел and коромысла.

9.2 For storage of elements клапанного the mechanism use small plastic packages with a corresponding label not to mix elements at installation and to establish all valves on the places.


2. Before removal of valves prepare plastic bags for their storage (9.2).

9.3 By means of the compressor of springs compress a spring, then remove сухарики


3. Compress a spring of the first valve and remove сухарики (9.3). Accurately release a spring and remove a plate, a spring and a spring saddle.

9.4 If the valve does not act in film, grind area round a flute on a rod of the valve a file


4. Remove the valve and an epiploon. If the valve does not act in film, remove a facet round a flute on a rod of the valve (9.4).
5. Similarly remove other valves.

9.6 Unscrew valves of an admission of the rarefied mix by means of special tool Mitsubishi MD998310 or a deep head


6. If it is necessary, remove valves of an admission of the rarefied mix (9.6).

9.7 Compress a spring of the valve by means of tool N MD998309


7. For valve removal compress a spring of the valve by means of the special tool (MD998309) (9.7), remove сухарики, a plate and a spring.
8. Remove consolidations from a valve rod.
9. After removal of valves clear and examine a head.


4.9. An engine partition - a dismantling order

4.11. A head of the block of cylinders - clearing and survey