Mitsubishi Colt (with 1983 for 1993 of release)
1. The maintenance instruction of cars Mitsubishi Colt / Lancer / Mirage / Galant / Eterna / Saporro / Sigma / Magna / Cordia / Tredia / Precis with 1983 for 1993 of release
2. Adjustment and current maintenance service
3. The engine
4. An engine partition
4.1. Technical characteristics
4.2. The general description
4.3. Engine major repairs - the general remarks
4.4. Diagnostics of the engine by means of the vacuum gauge, check of a compression and dismantle of the power unit (security measure)
4.5. Installation of the piston of cylinder N 1
4.6. Engine removal - the general description
4.7. The engine - removal and installation
4.8. Engine major repairs - alternative methods
4.9. An engine partition - a dismantling order
4.10. A head of the block of cylinders - dismantling
4.11. A head of the block of cylinders - clearing and survey
4.12. Valves - repair and installation
4.13. A head of the block of cylinders - assemblage
4.14. Pistons and rods - removal
4.15. A cranked shaft - removal
4.16. The block of cylinders - clearing
4.17. The block of cylinders - survey
4.18. Хонингование cylinders
4.19. Pistons and rods - survey
4.20. A cranked shaft - survey
4.21. Loose leaves radical and шатунных bearings - survey
4.22. An engine partition - an assembly order
4.23. Piston rings - installation
4.24. A cranked shaft - installation and check of a lubricant backlash of radical bearings
4.25. Installation of a back epiploon of a cranked shaft
4.26. Pistons and rods - installation and check of a lubricant backlash of the bearing
4.27. The first start of the engine after a partition
5. Systems of cooling, heating and an air conditioning
6. The power supply system and release of the fulfilled gases
7. An engine electric equipment
8. Systems of decrease in toxicity of exhausts
9. A mechanical transmission
10. An automatic transmission
11. Coupling and semiaxes
12. Brake system
13. A suspension bracket and a steering
14. A body
15. A body electric equipment
 











4a8e3442

4-27-pervyjj-zapusk-dvigatelya-posle-pereborki.html

4.27. The first start of the engine after a partition

Attention! At the first start of the engine check up fire extinguisher presence!
1. After engine installation once again check up all hoses of system of cooling and greasing. Add a transmission liquid if it is necessary.
2. Having removed spark plugs and having disconnected system of start of the engine, turn a cranked shaft of the engine a starter, the alarm bulb of low pressure of oil will not go out yet.
3. Establish spark plugs, connect wires of a high voltage and connect system of start of the engine.
4. Start the engine. For creation of necessary pressure in fuel system some time, however the engine can be demanded should be started without special problems.
5.  Warm up the engine to normal working temperature. Check up the engine and a transmission on presence of leaks of fuel, the oil, cooling liquid and a liquid automatic transmissions (if it is established).
6. Muffle the engine, and again check up level of oil and cooling liquid.
7. Disperse the car to 50-90 km/h at full turns of the engine, then wait, while speed will decrease to 50 km/h at closed throttle заслонке. Repeat this operation of 10-1-2 times. It will create loading on piston rings and will force them to nestle on walls of cylinders densely. Again check up levels of oil and cooling liquid.
8. Do not give the big loading on the engine the first 800 km of run (do not move constantly with vyso -
Which in the speed) and constantly watches oil level. The engine can consume oil during this period.
9. Through 800-950 km of run replace oil and the oil filter.
10. After that on the engine it is possible to give normal loading, however, do not overload it.
11. After 3500 km of run again replace oil and the oil filter.



4.26. Pistons and rods - installation and check of a lubricant backlash of the bearing

5. Systems of cooling, heating and an air conditioning