12-7-tormoznye-kolodki-barabannykh-tormozov-zamena.html
12.7. Brake колодки drum-type brakes - replacementAttention! Brake колодки it is necessary to replace simultaneously on both wheels. Attention! At replacement brake колодок it is recommended to replace also a returnable spring, a spring of an automatic regulator and clamping springs.
1. Lift the car and remove back wheels.
2. Remove the car from a manual brake.
3. Remove a brake drum.
Precis and Colt, Lancer, Mirage (models 1988 of release and earlier)
|
6.4а Elements of a back drum-type brake (model Colt, Lancer, Mirage and Precis 1988 of release and earlier)
1. A guard
2. A spring
3. A regulator
4. The lever of a manual brake
5. Brake колодки
6.
The piston
7.
The wheel cylinder
8. A pin
9. A clamping spring
10. A fixing spring
11. A returnable spring
12. Fastening
13. The final screw
14. A cover
|
|
6.4б Before removal of elements of a brake, clear their cleaning liquid of brakes and dry up them
|
|
6.4г With the help тонкогубцев disconnect a spring from колодок
|
|
6.4д Disconnect a returnable spring from колодок
|
|
6.4е Remove clamping springs with brake колодок
|
|
6.4ж Remove brake колодки and a regulator
|
|
6.4з Disconnect a rope of a manual brake from the lever of a manual brake - for this purpose take away a rope braid back and disconnect a rope from the lever
|
|
6.4и Disconnect brake колодки from each other
|
|
6.4к Remove the S-shaped clip from an axis of the lever of a manual brake (remove a clip only from the party opposite to the lever)
|
|
6.4л Disconnect a spring from a regulator...
|
|
6.4м... Then remove a regulator tip
|
|
6.4н Disconnect the lever of a manual brake from back brake колодки - establish the lever on new колодку and fix it by means of the Conformable clip
|
|
6.4о Disconnect a spring from the adjusting screw
|
|
6.4п Remove the S-shaped clip from a lobby underside колодки, then remove the adjusting screw
|
|
6.4р Clear the adjusting screw and grease with multipurpose greasing a carving - connect a regulator to a new lobby колодке and fix it by means of the S-shaped clip
|
|
6.4с Grease with a thin layer of high-temperature greasing sites on a guard, concerning brake колодок
|
|
6.4т Connect a rope of a manual brake to the lever of a manual brake
|
|
6.4у Establish back колодку on a guard of a brake and establish a clamping spring
|
|
6.4ф Establish a lobby колодку on a guard and establish a clamping spring
|
|
6.4х Establish a returnable spring
|
|
6.4ц Establish a fixing spring on колодки
|
|
6.4ч Pick up a clip spring under fastening колодок, and bend it from above fastenings (it is specified by an arrow) so that it has got to a groove on a clip
|
4. Check up and replace brake колодки, being guided by photos 6.4а, 6.4б, 6.4в, 6.4г, 6.4д, 6.4е, 6.4ж, 6.4з, 6.4и, 6.4к, 6.4л, 6.4м, 6.4н, 6.4о, 6.4п, 6.4р, 6.4с, 6.4т, 6.4у, 6.4ф, 6.4х, 6.4ц, 6.4ч
Precis and Colt, Lancer, Mirage (1989 of release and later), Cordia/Tredia, Galant
5. Clear a brake.
|
6.6а Elements of a back drum-type brake (model Cordia/Tredia)
1 Guard of a brake
2 Returnable spring
3 Spring
4 Lever of a manual brake
5 Brake колодка
6 Brake drum
7. A pin
8. A spring
9. The terminator
10 Latch
11. A fixing spring
12. The adjusting lever
13. Распорка
14 Clamping spring
15 Fastening
16 Pin
|
|
6.6в Disconnect a regulator spring, then remove a spring and the lever (are specified by arrows)
|
6. Disconnect a spring from a regulator or the regulator lever (depending on model) and remove to the lever and a spring ( 6.6а, 6.6б and 6.6в).
7. Dissolve колодки in the parties and remove a regulator.
8. Remove a returnable spring.
9. Remove clamping springs brake колодок.
10. Remove a lobby колодку from a brake guard, then disconnect a rope of a manual brake from the lever.
11. Clear the adjusting screw and grease its carving with multipurpose greasing ( 6.4р).
12. Grease with a thin layer of high-temperature greasing sites on a guard, concerning brake колодок ( 6.4с).
13. Establish the lever of a manual brake on new back brake колодку ( 6.4к).
14. Connect a rope to the lever of a manual brake and establish back колодку on a guard. Establish a clamping spring.
15. Establish a lobby колодку on a guard and establish a clamping spring.
16. Establish a returnable spring on колодки.
|
6.17 Check up, that regulator cuts (or распорки) have got to cuts on колодках
|
17. Dissolve колодки in the parties and establish a regulator ( 6.17).
18. Establish the lever of a regulator and a spring.
All models
|
6.19 as much as possible admissible diameter of a brake drum is specified in drum surfaces
|
19. Before installation check up a brake drum on presence of cracks, scratches or stains. As much as possible admissible diameter of a drum is specified on the drum ( 6.19).
20. Establish a brake drum and adjust bearings of a back wheel.
21. Establish a wheel and lower the car on the earth.
22. Put the car on a manual brake and squeeze out a brake pedal some times to adjust position brake колодок.
|
|