Mitsubishi Colt (with 1983 for 1993 of release)
1. The maintenance instruction of cars Mitsubishi Colt / Lancer / Mirage / Galant / Eterna / Saporro / Sigma / Magna / Cordia / Tredia / Precis with 1983 for 1993 of release
2. Adjustment and current maintenance service
3. The engine
4. An engine partition
5. Systems of cooling, heating and an air conditioning
6. The power supply system and release of the fulfilled gases
7. An engine electric equipment
7.1. Technical characteristics
7.2. The general information
7.3. The accumulator - start of the engine by means of the second accumulator
7.4. The accumulator - removal and installation
7.5. Accumulator wires - check and replacement
7.6. Ignition system - the general description and safety measures
7.7. Ignition system - check
7.8. The ignition coil - check and replacement
7.9. The ignition distributor - removal and installation
7.10. Vacuum-proof-reader of a corner of an advancing of ignition - check and replacement
7.11. An igniter - replacement
7.12. Check and replacement of reception coil Cordia / Tredia 1.8L Turbo [1984 and 1985); Colt, Lancer, Mirage 1.6L (1985)
7.13. A centrifugal regulator - check and replacement of elements
7.14. An air backlash of the reception coil of the distributor of ignition - check and adjustment
7.15. System of additional charge of the accumulator - the general description and safety measures
7.16. System of additional charge of the accumulator - check
7.17. The generator - removal and installation Cordia, Precis and Tredia
7.18. A pressure regulator / generator brushes - replacement 1988 Precis (with generator Bosch)
7.19. System of start of the engine - the general description and safety measures
7.20. A starter - check
7.21. A starter - removal and installation
7.22. The involving relay of a starter - removal and installation
8. Systems of decrease in toxicity of exhausts
9. A mechanical transmission
10. An automatic transmission
11. Coupling and semiaxes
12. Brake system
13. A suspension bracket and a steering
14. A body
15. A body electric equipment
 











4a8e3442

7-18-regulyator-napryazheniya-shhetki-generatora-zamena-1988.html

7.18. A pressure regulator / generator brushes - replacement 1988 Precis (with generator Bosch)

1. Remove the generator.

17.2 For removal of a regulator of pressure/holder of brushes turn off two fixing screws (are specified by arrows) and remove the holder of brushes


2. Turn off fixing screws of a regulator of pressure (17.2).

17.3 Measure length of brushes by means of a small ruler - if they more shortly, than 2-3 mm, replace them


3. Remove the holder of brushes and measure length of brushes. If they are shorter, than 4,6 mm, replace them. (17.3)

17.4 For removal of the worn out brushes from the holder accurately отпаяйте wires of brushes


4. Отпаяйте wires of brushes (17.4) also remove brushes and springs.
5. Installation is spent upside-down removals. Reliably solder new brushes.
All other models (with generator Melco)
6. Remove the generator.
7. Turn off bolts, крепящие половинки the generator.
8. Clamp a forward part of the generator in a vice.
9. Turn off all nuts from a generator underside.

17.10а For simplification of dismantling of the generator heat up a bearing casing
1. A soldering iron
2. A bearing casing


10. A powerful soldering iron heat up a back box (17.10а

17.10б By means of two screw-drivers divide половинки the generator

) And by means of two screw-drivers wring out a back casing (17.10б).

17.11 Elements of generator Melco

1 Pulley of the generator 2. An epiploon
3 Rotor
4 Back bearing
5. Bearing fastening
6. The forward bearing
7. A forward arm
8. Статор
9. The plug
10. A plate
11. A regulator and the holder of brushes
12. A brush
13. A brush spring
14. The plug
15. A reducer
16. A back arm


11. Отпаяйте the holder of brushes/regulators (17.11).

17.12а If brushes are worn out further a restrictive line, it is necessary to replace them
1 Restrictive line
2 Restrictive line


17.12б At replacement of brushes solder wires in following points
1. Solder


12. Examine brushes and replace them if it is necessary (17.12а and 17.12б).

17.13 At installation of new brushes they should act from the holder on certain size


13. At installation of new brushes solder the ends of wires of brushes so that brushes acted from the holder on 1,9-2,9 mm (17.13).

17.14 At connection of two половинок together stretch a wire through a back casing and the holder of brushes for fixing of brushes in the holder

1. A wire
2 Brush
3 Wire



14. Assemblage is spent upside-down dismantlings (17.14).


7.17. The generator - removal and installation Cordia, Precis and Tredia

7.19. System of start of the engine - the general description and safety measures