6-17-trosik-akseleratora-snyatie-ustanovka-i-regulirovka.html
6.17. An accelerator rope - removal, installation and adjustmentModels without cruise-control system
Cordia, Tredia, Colt, Lancer, Mirage (except MPI) and Precis (except MPI)
1. On carburettor engines remove the air filter.
|
16.2 Turn off an adjusting nut (it is specified by an arrow) and disconnect a rope of an accelerator from an arm
|
2. Turn off an adjusting nut ( 16.2) and remove a rope from an arm.
|
16.3а Remove the furnish panel under the panel of devices and disconnect a rope in a point specified by an arrow.
|
|
16.3б Disconnect a rope from a fire-prevention partition turning off two fixing bolts and remove directing a rope from a partition.
|
3. Disconnect a rope from the carburettor and a gas pedal. Remove a rope from a back wall of an impellent compartment ( 16.3а and 16.3б).
4. Remove a rope from the car.
5. Installation is spent upside-down removals.
Galant, Colt, Lancer, Mirage and Precis (MPI) Removal and installation
|
16.6 Elements of a rope of an accelerator of models Galant, Colt, Lancer, Mirage and Precis (without the cruise-control)
1 Rope
2 Adjusting bolt
3 Rope
4 Plug
5 Arm
6 Socket of connection of the switch of an accelerator (model with an automatic transmission]
7 Returnable spring
8 Pedal of an accelerator
9 Checks
|
6. Get a rope from arms, disconnect it from a pedal of gas and the case of a throttle and remove from the car ( 16.3а, 16.3б and 16.6).
7. Installation is spent upside-down removals.
Adjustment
8. Warm up the engine and check up speed of idling. Adjust it if it is necessary. Muffle the engine.
9. Press a pedal of an accelerator and check up, that the lever throttle заслонки moved smoothly, and completely opened заслонку.
10 Include ignition for 15 seconds
11 Turn off two bolts, крепящих a rope near the throttle case
12 Pull a rope and tighten two bolts Check up, that the lever throttle заслонки concerned a rod of a vacuum diaphragm
Models with cruise-control system
Cordia and Tredia
Rope of a pedal of an accelerator
|
16.13 Elements of fastening of a rope of an accelerator on models Cordia and Tredia with cruise-control system. Adjusting nuts are specified by arrows
|
13 Turn off adjusting nuts and disconnect a rope from the lever throttle заслонки and an arm ( 16.13)
14 Remove a rope
15 Installation is spent upside-down removals
Rope of the executive mechanism
16 Disconnect a rope from the lever throttle заслонки and the executive mechanism and remove it from the car Installation it is spent upside-down removals
17 After installation, eliminate rope sagging, having tightened adjusting nuts when the engine works in an idling mode
Galant
Removal and installation
18 Remove a casing of the executive mechanism
|
16.19 Elements of fastening of a rope of an accelerator on model Galant with cruise-control system
1 Rope of an accelerator And
2 Executive mechanism of system of the cruise-control
3. An accelerator pedal
4. The switch
5. A connecting link In
8. A connecting link And
7. The lever throttle заслонки
8 Adjusting bolts
9. The terminator
10. An accelerator rope In
11 Adjusting nut And
12. A counternut
|
19 Turn off an adjusting nut and remove a rope from an arm ( 16.19)
20 Disconnect a rope from a connecting link Disconnect a rope from a pedal and the case of a throttle and remove it from the car ( 16.3а)
21 Installation is spent upside-down removals
Adjustment
22 Warm up the engine and check up speed of idling Adjust it if it is necessary Muffle the engine
23 Press a pedal of an accelerator and check up, that the lever throttle заслонки moved smoothly, and completely opened заслонку
24 Turn off adjusting nuts of a rope Include ignition for 15 seconds
25 When a connecting link (And (concerns an emphasis ( 16.19), tightening up an adjusting nut (And (adjust a rope tension so that a link (And (began to depart from an emphasis, then turn off a nut (And (on two turns
26. Having tightened up an adjusting nut (), pull a rope so that the lever on a connecting link () concerned the lever on a link ().
27. Turn off two fixing bolts of a rope near the case of a throttle and pull a rope Twirl counternuts of an intermediate link and two bolts, крепящих a rope near the throttle case.
Colt, Lancer, Mirage (MPI)
Removal and installation of a rope of a pedal of an accelerator
|
16.28 Elements of fastening of a rope of an accelerator on models Colt, Lancer, Mirage MPI
1 Rope of an accelerator And
2 Adjusting bolt
3 Terminator
4 Connecting link And
|
28. Get a rope from fixing arms and disconnect it from a connecting link and an accelerator pedal. Get a rope through a back wall of an impellent compartment and remove it from the car. Installation is spent upside-down removals ( 16.28, 16.3а and 16.3б).
Removal and installation of a rope of the lever throttle заслонки
29. Get a rope from fixing arms, disconnect it from a connecting link and the lever throttle заслонки and remove a rope from the car. Installation is spent upside-down removals
Adjustment
30. Remove the air filter.
|
16.31 For adjustment of a rope throttle заслонки tighten up adjusting bolts
1. Adjusting bolts
2. A plate
|
31. Having tightened up adjusting bolts, adjust a tension of a rope of the lever throttle заслонки that it had a small free course ( 16.31).
32. Check up, that the lever concerned the switch of system of idling.
33. Check up, that the connecting link concerned an emphasis ( 16.28), then turn off an adjusting bolt of a rope of a pedal of an accelerator and pull a rope
34. Check up, that throttle заслонка it opened completely and closed by pressing an accelerator pedal.
|