Mitsubishi Colt (with 1983 for 1993 of release)
1. The maintenance instruction of cars Mitsubishi Colt / Lancer / Mirage / Galant / Eterna / Saporro / Sigma / Magna / Cordia / Tredia / Precis with 1983 for 1993 of release
2. Adjustment and current maintenance service
3. The engine
4. An engine partition
5. Systems of cooling, heating and an air conditioning
5.1. Technical characteristics
5.2. The general information
5.3. Antifreeze - the general information
5.4. The thermostat - check and replacement
5.5. A radiator - removal and installation
5.6. The fan of cooling of the engine - check and replacement of elements
5.7. The gauge of temperature of a cooling liquid - check and replacement
5.8. A broad tank of system of cooling - removal and installation
5.9. The water pump - check
5.10. The water pump - replacement and installation.
5.11. The engine of system of heating and an air conditioning - removal and installation.
5.12. A heater radiator - replacement
5.13. Air and heating central air - replacement, installation of wires.
5.14. Air central air - check and routine maintenance
5.15. A reception tube of the conditioner - removal and installation
5.16. The compressor of a central air of air - removal and installation
5.17. The condenser of a central air of air - removal and installation
6. The power supply system and release of the fulfilled gases
7. An engine electric equipment
8. Systems of decrease in toxicity of exhausts
9. A mechanical transmission
10. An automatic transmission
11. Coupling and semiaxes
12. Brake system
13. A suspension bracket and a steering
14. A body
15. A body electric equipment
 











4a8e3442

5-10-vodyanojj-nasos-zamena-i-ustanovka.html

5.10. The water pump - replacement and installation.

Attention! Do not start the given procedure until the engine will not cool down.
Replacement
1. Disconnect a wire of the minus plug of the accumulator.
2. Merge cooling liquid.

9.3 At first turn off fixing bolts, then remove приводные belts.


3. Remove the left engine mount and turn off fixing bolts of the water pump (9.3).
4. Remove приводные belts and the block which is in the end of the water pump.
Attention!

9.4 At first unscrew a bolt In, then it is necessary to weaken a bolt And and to disconnect a belt of a central air of air. Now unscrew bolts And and With.


Disconnect all fixing knot at removal of a belt of a central air of air (9.4).
5. Remove a gear belt of a drive and the tension device.
6.  Remove  an arm  of the generator of an alternating current from the water pump.
7. Turn off fixing bolts and remove the pump from the engine.
Installation
8. Clear carving apertures and a carving of fixing bolts.
9. Check up, whether old and new water pumps are identical.
10. Remove traces of an old lining and a sealing ring from the engine.
11. Clear adjoining surfaces of the engine and the pump solvent or acetone.
12. Establish a new sealing ring in a flute and humidify a ring охладительной with a liquid.
13. Apply a thin film hermetic on a sealant from the motor and connect it to the water pump. Slightly tighten fixing bolts and establish a sealant into place.
14. Accurately attach the pump to the engine, and slightly tighten fixing bolts. It is necessary to notice, that one bolt on the left side of the water pump is a little bit longer than others.

9.7а Unscrew fixing bolts (are specified by arrows).


9.7б Fixing details of the water pump.


15. Establish all remained bolts, and gradually tighten them till the demanded moment of an inhaling.
16. Establish all remained details.
17. Fill system of cooling and check up a tension приводных belts.
Start the engine and check up system on tightness.



5.9. The water pump - check

5.11. The engine of system of heating and an air conditioning - removal and installation.