Mitsubishi Colt (with 1983 for 1993 of release)
1. The maintenance instruction of cars Mitsubishi Colt / Lancer / Mirage / Galant / Eterna / Saporro / Sigma / Magna / Cordia / Tredia / Precis with 1983 for 1993 of release
2. Adjustment and current maintenance service
3. The engine
3.1. Technical characteristics
3.2. The general information and engine identification
3.3. The repair operations, which carrying out it is possible without removal of the engine from the car
3.4. A cover of valves - removal and installation
3.5. Коромысла - removal, check and installation
3.6. Springs of valves, fastenings and overlays - replacement
3.7. Hydraulic regulators of valves - removal, check and installation
3.8. Газораспределительный a belt and asterisks - removal, check and installation
3.9. A forward epiploon of a cranked shaft - replacement
3.10. Camshafts - removal, check and installation
3.11. An inlet collector - removal and installation
3.12. A final collector - removal and installation
3.13. A head of cylinders - removal and installation
3.14. The oil pallet - removal and installation
3.15. The oil pump - removal, check and installation
3.16. A flywheel - removal and installation
3.17. A back epiploon of a cranked shaft - replacement
3.18. Engine support - check and replacement
4. An engine partition
5. Systems of cooling, heating and an air conditioning
6. The power supply system and release of the fulfilled gases
7. An engine electric equipment
8. Systems of decrease in toxicity of exhausts
9. A mechanical transmission
10. An automatic transmission
11. Coupling and semiaxes
12. Brake system
13. A suspension bracket and a steering
14. A body
15. A body electric equipment
 











4a8e3442

3-4-kryshka-klapanov-snyatie-i-ustanovka.html

3.4. A cover of valves - removal and installation

1. Disconnect a wire of the minus plug of the accumulator.
2. Remove the air filter.

3.3 Cautiously disconnect wires of spark plugs from clips


3. Disconnect wires of spark plugs and arms of ropes from a cover of valves (3.3).
Attention! In engines DOHC remove the central cover to open access to spark plugs.
4. Mark and disconnect ropes and hoses of an exhaust system which are connected to a cover of valves or lie over it.

3.5а Unscrew bolts of a cover of valves (are specified by arrows) - the engine in volume of 2,0 l is shown


3.5б the Cover of valves of engine SOHC, коромысла and a camshaft
1. Газораспределительный a belt
2. A camshaft asterisk
3. A camshaft epiploon
4. Semicircular consolidation
5. A camshaft
6. Коромысла
7. Semicircular consolidation
8Вентиляционный a hose
9. A rope clip
10. A cover of valves



3.5с the Cover of valves of engine DOHC, коромысла and a camshaft
1. Газораспределительный a belt
2. A camshaft asterisk (inlet valves]
3. A camshaft asterisk (final valves)
4. A camshaft epiploon
5. Covers of bearings of a camshaft
6. A cover  of the bearing  of a camshaft
7. A camshaft (inlet valves)
8. A camshaft (final valves)
9. A cover  of the bearing  of a camshaft
10. A cover of the bearing of a camshaft
11. Semicircular consolidation 12. A ventilating hose


5. Unscrew bolts of a cover of valves (3.5а, 3.5б, 3.5с) and remove a cover. If the cover has strong stuck to a head of cylinders, cautiously knock on it with a wooden hammer.
6. Carefully clean a cover, having removed traces of an old lining.
7. Establish a new lining on a cover. Put on a cover a head of cylinders and insert bolts.
Attention! Do not forget to establish semicircular consolidation in a head of cylinders (3.5а, 3,5б). Put on a back part of consolidation a hermetic small amount, establish consolidation and put hermetic on its top part.
8. Tighten bolts till the moment of an inhaling specified in technical characteristics. After you have finished installation, get the engine and examine it on presence of leaks.


3.3. The repair operations, which carrying out it is possible without removal of the engine from the car

3.5. Коромысла - removal, check and installation