10-6-trosik-rychaga-selektora-avtomaticheskojj-korobki-peredach-snyatie.html
10.6. A rope of the lever of the selector of an automatic transmission - removal, installation and adjustmentRemoval
1. Disconnect a wire of the minus plug of the accumulator
|
5.2 Rope of the selector fastens to the lever on a transmission with the help checks and washers and to an arm by means of a clip or two nuts (located on each side an arm)
|
2. In an impellent compartment remove the air filter, disconnect a rope from the lever on a transmission and remove it from an arm ( 5.2)
3. Lift the car and establish it on support
4. From below the car turn off fixing bolts and rope nuts
|
5.5а Elements of the selector of an automatic transmission of models Cordia/Tredia, and also Colt, Lancer, Mirage and Precis early years of release
1 Fixing screw 2 Handle
3 Console (is not shown)
4 Bulb
5 Selector panel
6 Bolt
7 Adjusting nuts of a rope
8 Fixing "a bolt
9 Nuts of a fixing arm of a rope
10 Fixing nuts of the lever of the selector
11 Mechanism of the selector
12 Lining
13 Rope
14 Lever of the selector
|
|
5.5б Elements of the selector of an automatic transmission of models Colt, Lancer, Mirage and Precis late years of release
1. A console shelf
2. The back console
3. The forward console
4. The selector
5. A rope
|
|
5.5в Elements of the selector of an automatic transmission of models Colt, Lancer, Mirage and Precis late years of release
1. A socket of connection of the switch of raising transfer
2. The handle
3. A casing
4. The button
5. A spring
6. The switch of raising transfer
7. A bulb
8. The selector panel
9. The plug
10. A spring pin
11. A rod
12. The bottom spring
13. A pin
14. A spring
15. Fastening
16. A steel ball
17. The lever
18. Plugs
19. An arm
|
|
5.5г Elements of the selector of an automatic transmission of model Galant of early years of release
1. The button
2. The screw
3. The Casing
4. The handle
5. The plug
6. A rod
7. The lever the selector
8. The plug
9. A clip
10. An adjusting nut
11. A regulator
12. The plug
13. A rope
14. A rope tip
15. The panel
16. The index
17. The selector panel
18. A bulb
19. An arm
|
|
5.5д Elements of the selector of an automatic transmission of models Galant 1987 and 1988 of release
1. An internal box
2. Заглушка
3. The back console
4. The left casing
5 Right casing
6. The furnish panel
7. The forward console
8. A socket of connection of the switch of raising transfer
9. The screw
10. The screw of fastening of the handle
11. The button
12. A spring
13. The handle
14. A casing
15. The selector panel
16. The index
17. A socket of connection of a bulb
18. The bottom selector panel
19. A cutting lock ring
20. A pin
21. The air filter
22. A rope winding
23. A clip
24. The check
25. The plug
26. A rope
27. An adjusting nut
28. A regulator
29. The selector lever
|
|
5.5е Elements of the selector of an automatic transmission of model Galant of 1989 of release and later
1 Selector panel
2 Switch of an operating mode of a transmission
3 Lateral casing
4 Lateral panel of a manual brake
5 Console
6 Lever of the selector
7 Clip
8 Fixing clip
9 Clip
10 Fixing clip
11 Rope
12 Plug
|
|
5.5ж Elements of the selector of an automatic transmission of model Galant of 1989 of release and later
1 Socket of connection of the switch
2 Casing
3 Handle
4 Button
5 Switch of raising transfer
6 Pin
7 Button
8 Spring
9 Selector panel
10 Index
11 Bottom selector panel
12 Nest
13 Plug
14 Lever of the selector
15 Plug
16 Arm
|
6. In salon remove the handle of the lever of the selector and the console Disconnect a rope from the lever and remove the selector lever ( 5.5а, 5.5б, 5.5в, 5.5г, 5.5д, 5.5е and 5.5ж)
7. Remove a rope of the selector from the car
Installation
8 Installation is spent upside-down removals
Adjustment
9 Translate the selector lever in position of neutral transfer
|
5.10 Turn the lever of the selector for reception of a demanded backlash (), the oblique party () plugs should be turned to the driver
1 Plug
2 Lever
|
10 Having tightened up the plug, adjust a backlash between the plug and the lever ( 5.10)
11. Establish the console and the handle of the lever of the selector.
13. Check up work of the mechanism of the selector. Adjust blocking switch if it is necessary.
|
|